the kitchen guy
journal/Frameless European cabinetry explained

Frameless Kitchen Cabinets: Construction, Reveals, Wider Drawers

How frameless European cabinets are built, why their reveals are so tight, and why the drawers hold more than a framed box of the same width.

· the kitchen guy

frameless cabinetry is the quiet half of what we build. it has no face frame, no visible stiles, and nothing standing between you and the inside of the box. what you see is a door, a gap, and the next door.

it looks simple. the simplicity comes from construction that is more exacting than it appears. here is how a frameless cabinet goes together, where the tight reveals come from, and why the drawers are wider.

what "frameless" actually means

a traditional american cabinet is a box with a hardwood frame, usually 1½" wide at the stiles, applied to the front. the doors and drawers sit on that frame, or inside it in the case of inset.

a frameless cabinet drops the frame. the case itself is the structure: two sides, a bottom, a top or stretchers, and a back, all joined with precision-bored dowels and glue. the door covers the front edge of the case completely. the full-overlay look comes from the box, not from an applied part.

in our range, this is TKG Standard (European frameless) and TKG Custom (European bespoke). TKG Inset is the framed, american-made line. the collections page shows how the three sit side by side.

inside the box

because the case carries everything, the panels matter. ours are ¾" (19 mm) core with a bonded interior surface and edge-banded fronts. a thinner panel flexes under a loaded drawer and the reveals drift over time.

  • 32 mm system. hinge plates, shelf pins and drawer runners all align to a grid of holes bored 32 mm apart, set back 37 mm from the front edge. this is why a shelf pin, a hinge and a runner can all be moved without drilling new holes.
  • captured back. the back panel sits in a groove, or is fixed and glued to the case, so the box stays square. a loose stapled back is a sign of a cabinet that will rack.
  • adjustable legs. base cabinets sit on leveling feet with about ±1" of travel under a 4½" toe-kick, and the plinth clips on afterward.
  • rail hanging. wall cabinets hang on a steel rail with adjustable hangers, so they can be tuned for height and tilt after they are up.

that last point matters in new york. pre-war co-op walls are rarely plumb. a ¼" lean over 30" of height is common, and a brownstone floor can drop an inch across a 12-foot run. leveling legs and adjustable hangers let the boxes stay true and let the doors line up, even if the room does not.

reveals: where the thin gap comes from

on a frameless run, the gap between doors is typically 2–3 mm, about 1/8". it is a visual choice, but it is made possible by the hardware.

each door hangs on concealed cup hinges that adjust three ways: up and down, in and out, and side to side. a good installer can set every door in a run to the same gap and the same plane, and can re-tune it in five years when the house has settled. the door is not planed to fit. the hinge is adjusted to the door.

that is a different philosophy from inset, where the door sits inside a frame and the reveal is a hand-fitted 3/32". both are precise. frameless gets there by adjustment, inset by fitting. neither is better, but they suit different rooms.

the tight reveal also changes how you choose a door. frameless fronts tend toward flat slab profiles, where the gap reads as a clean line. you can browse slab and other profiles in our door styles gallery. a grained surface such as rift cut white oak in thorn works well here, because continuous grain across a run of doors needs those narrow gaps to read as one surface.

why the drawers are wider

this is the practical advantage most people miss.

in a framed cabinet, the opening is the width of the box minus the two stiles. at 1½" each, you lose roughly 3" of width before you even fit a drawer. the drawer box then sits inside that opening with clearance for the runners.

in a frameless cabinet, the drawer box sits between the case sides. the only things taken from the width are the two ¾" panels and the runner clearance. on a 30" cabinet, the usable drawer interior is typically 1.5–2" wider than in a framed cabinet of the same width.

that sounds small. consider what it changes:

  • a 30" drawer takes a full-size dinner plate stack with room to spare, rather than a tight fit.
  • a 36" pot drawer takes a 12" skillet beside a 10" one, instead of one over the other.
  • a 24" cabinet can hold a standard 21" knife-and-utensil insert plus a divider.

across an entire kitchen, it adds up to a couple of extra drawers' worth of storage, with no change to the footprint. in a 9-foot galley in a pre-war building, where you cannot add a single inch of cabinet, that is real capacity. it is also why we specify drawer bases over door bases in almost every plan.

where frameless works best in new york

narrow galleys and city kitchens. when the aisle is 40–48" and every inch of storage counts, the wider drawers earn their place. you also gain a slightly larger door opening for pull-outs and tall pantries.

lofts and modern apartments. long, flat runs with minimal reveals suit open plans, and slab doors in veneer or paint stay calm next to concrete, steel and glass. a light veneer like ice walnut keeps a Tribeca-style loft kitchen warm without competing with the architecture.

access and delivery. cabinets arrive as finished boxes, and most pass through a standard 30" door and an older elevator. brownstone stairs and tight turns are a planning item for any cabinet, but a frameless box has no protruding face frame to catch the wall.

for Manhattan projects we show frameless and inset next to each other, so you can judge the look at actual scale. see our Manhattan page for how we work in the city.

the trade-offs, plainly

frameless is not right for every house.

  • traditional rooms. a raised panel or applied molding door looks most at home in a frame. if you are restoring a brownstone parlor floor, inset is usually the better answer.
  • very uneven walls. a frame can be scribed, and a frameless side panel needs a filler or scribe strip. it is easy to handle, but it needs planning.
  • exposed edges. with no frame, the front edge of the case is visible when a door is open. we use matching edge-banding, but the detail is there.

if you are weighing it up, a useful test is to ask what you want to see when the doors are closed. if the answer is "one clean surface," frameless wins. if it is "furniture," look at inset.

if you need a team to take the cabinetry from drawing to installed kitchen, our sister design-build studio is at thekitchenguy.pro.

see it in person

the gap between a cabinet drawing and a cabinet in your hand is large. open a drawer, close a door, and look at the reveal against the light. request a sample door or book a showroom visit in Manhattan or Cedarhurst, or by appointment in South Florida.

keep reading

see it in person

book a showroom visit.

Manhattan and Cedarhurst, or South Florida by appointment.

We reply to every inquiry. Typical response time is two business days.